|
所在平台: Udemy |
课程主页: https://www.udemy.com/course/reinforced-concrete-beam-design-with-rapt/
课程评论：没有评论
课程名称：使用 RAPT 进行钢筋混凝土梁设计 课程概述：RAPT 是一个非常强大的钢筋和预应力混凝土结构设计软件。本课程旨在教会您如何使用该软件来实际设计和分析钢筋混凝土梁。同时，我将介绍如何在软件中利用不同工具模型特殊设计条件并遵循具体的规范要求。本课程将逐步演示如何在 RAPT 中建模钢筋混凝土梁，您将了解程序中不同工具的使用方法，以便在建模时处理不同的竖向或横向步骤、混凝土层和混凝土构件。 课程内容包括： - 设置特定规范要求以及这些要求在规范中提到的位置。 - 指定不同的跨度、板/梁厚度以及梁的支撑条件，包括柱、刀边或固定支撑。 - 按照规范要求设置梁的尺寸和有效宽度，并定义下沉面和下沉帽的区别。 - 定义横向梁以及 RAPT 中带和梁的不同之处。 - 在程序中定义不同的负载情况和组合，查看规范要求，并施加线性负载、压力、面积负载、点负载和力矩。 - 为新建和已有的梁指定钢筋，定义上部和下部钢筋，审查具体设计数据并进行必要的修改。 - 最后查看梁设计的结果，并进行强度和服务性检验。 课程结束时，您将掌握如何在 RAPT 中实际设计和分析钢筋混凝土梁，并学会利用软件中的各种工具模型特殊设计条件。我的目标是通过传授实践知识为学生增加价值，欢迎随时提问。
RAPT is a very powerful program for reinforced and pre-stressed concrete design of structural systems and the aim of this course is to teach you how to use this software in order to practically design and analyze a reinforced concrete beam. Also, I will explain how to use different tools in this program to model special design conditions along with the specific code requirements.In this course, we will have a Step by step modeling of a reinforced concrete beam in RAPTYou will learn about the different tools in Rapt in order to model different vertical or horizontal steps, concrete layers and concrete elements in this programI will also explain how to set code-specific requirements and where in the code these requirements are mentioned.Also, you will learn how to specify different spans and slab/beam thicknesses as well as different support conditions for our beams which can be columns, knife edges, or fixed supportsYou will see how we can set the beam's dimensions and effective width as per the requirements of the code and also how to define drop panels and drop capes and what are the differences between these two. I will explain how to define a transverse beam and what are the differences between band and beam in RAPT.In the next section, you will see how we can define different load cases and load combinations in the program and look at the requirement of the code as well as applying different line loads, pressures, area load, point load, and moments on the Beam.You will learn how to specify reinforcement for a new and existing beam and define the top and bottom reinforcement and then we will go through the code specific design data and see how to modify them if required.Finally, we will look at the results of the beam design and do the strength and serviceability check.By the end of this course, you will learn how to practically design and analyze a reinforced concrete beam in RAPT and also how to use different tools in this program to model special design conditions.My goal is to add value to my students by conveying my practical knowledge, so please do not hesitate to ask if you ask any questions.
