|
所在平台: Udemy |
课程主页: https://www.udemy.com/course/piperack-piping-and-stress-analysis/
课程评论：没有评论
**课程名称：** 管道支架管道及应力分析 **课程概述：** 本课程深入讲解了工艺装置中至关重要的管道支架设计。课程强调，尽管设计方法多种多样，但其基本概念始终一致。本课程不仅涵盖了管道支架设计的基础知识，还重点阐述了应力分析的原理。 **课程内容涵盖：** * **管道支架布局：** * 所需输入信息 * 概念设计：互连图、根据互连图计算支架宽度和层数、操作/维护/通道要求、决定横梁的高度 * 设计考虑因素：管道在支架上布置的指导原则 * 边界配置的说明 * 支撑与柔性要求 * 支架上的设备 * 支架上方的平台 * **应力分析：** * 由 Anup Dey 先生贡献（特别感谢其宝贵贡献） * 详细介绍了管道支架管道相关的各种应力分析概念。 * 结合行业实践以及各种规范和标准，对 CAESAR II 软件中的实际建模进行了详细讲解。 * **主要活动：** * 准备工作：所需文件/输入信息 * Caesar II 中的输入参数：设置单位系统、使用的规范和标准 * 分步建模：CAESAR II 的各种工具（管道、管件、支架） * 建模/分析中的最佳实践 * 管道支架管道建模 * **其他涵盖主题：** * 膨胀弯 * PSV 管道分析 **总结：** 本课程全面覆盖了管道支架布局和应力分析的大部分相关概念，并提供了 CAESAR II 软件的分步建模指南，这是每位管道工程师都应掌握的技能。希望本课程能帮助大家提升专业知识，祝学习愉快！
Pipe rack is integral part of any process plant, there are many ways to perform the design, but the basic concepts behind the same is always same. This course covers a lot fundamentals along with the stress analysis basis.Following modules have been covered and explained in systematic way. All the design considerations have been captured and explained in such a way that whole design section is covered.Major topics under Layout are: •Inputs required•Conceptual Design-Interconnection Diagram-Calculating rack width and no. of Tiers from Interconnection Diagram-Operational/Maintenance/Access requirements-Deciding the Elevation of transverse beamsDesign Considerations•Guidelines for placing lines on PiperackBattery Limit Configurations have been explained•Supporting & Flexibility requirements•Equipment on Piperack•Platforms above PiperackStress Analysis: Complete content is prepared by Mr. Anup Dey (Special Thanks for valuable contribution)/Various concepts related to Stress Analysis keeping in view the Piperack piping have been captured and explained in detail. Actual modelling in CAESAR II is done and explained in detail w.r.t. industry practices and various codes & standards.Following major activities have been capturedSetting Ground WorkDocuments/Input RequiredInput parameters in CaesarSettings Unit Systems·Codes & Standards usedStep By Step ModellingVarious tools of Caesar IIPipeline, Fittings, SupportsBest Practices while modeling/AnalysisModeling of Piperack pipingAlong with above following topics have been coveredExpansion loopsPSV piping analysisThe Complete course covers most of the Layout & Stress Analysis related concepts, step by step modelling in Caeser-II has been defined which every piping engineer should understand, hope this adds value to the knowledge. Happy Learning!!
