|
所在平台: Udemy |
课程主页: https://www.udemy.com/course/pic-microcontroller-using-mikroc-for-pic-from-scratch/
课程评论：没有评论
课程名称：从零开始的MikroC PIC微控制器应用 课程概述：本课程旨在教授如何使用PIC微控制器进行各种项目的开发。您将学习如何将各种传感器或模块与PIC微控制器接口，并能够在触摸屏（如Nextion/DWIN）、液晶显示器（如LM016）、七段显示器以及PC/笔记本电脑上显示输出。课程中将使用MikroC for PIC库来实现PWM、UART、转换、LCD、ADC等功能，与PIC微控制器进行硬件接口。您将对MikroC for PIC编译器有更深入的了解，并使用Proteus进行仿真。 课程将从简单的理论开始，例如微控制器的定义和嵌入式系统的介绍，逐步深入PIC16F877A的相关知识。我们将介绍编译软件，搭建PICKIT3的硬件进行读/写操作，并编写第一个LED闪烁程序。接下来，我们将熟悉MikroC库，并在每节课中开始一个新的项目的编程。 您将在课程中学习到的相关软件包括： 1. MikroC for PIC 2. Proteus 3. PICKIT3编程工具 4. 定时器计算器 5. Nextion编辑器 6. DWIN DGUS 课程将涵盖的传感器/模块/电子元件包括： 1. 光敏电阻（LDR） 2. LM-35温度传感器 3. 七段显示器 4. LM016液晶显示器 5. TIP-122晶体管 6. 电阻 7. 可变电阻 8. 按钮 9. LED灯 10. 直流电机 11. HC-05蓝牙模块 12. HC-12射频模块 13. USB转TTL设备（如CH340/FT232） 14. 触摸按钮模块 15. 限位开关 16. 切换开关 17. 倾斜检测模块 18. 红外LED 19. 障碍检测模块 20. L298N电机驱动模块 课程时间有限，我们将尽可能覆盖更多内容。
This course will allow you to learn how to use PIC microcontrollers to make any project. You will be able to interface any sensor or module with a PIC microcontroller.You will be able to display outputs on touch screens like nextion/dwin, LCDs like LM016, 7-segment displays or a PC/Laptop.You will be able to use MikroC for PIC PWM, UART, Conversion, LCD, ADC and other libraries to interface sensors/modules with PIC microcntroller.You will get better grip on MikroC for PIC compiler.You will be using Proteus for simulation.You will get your hands on making a start-up boards under my supervision for reading and writing data to the PIC microcontroller using MikroC for PIC.My aim will be to start from some simple theory like what is a microcontroller ? What is embedded systems ? Then we will move on to what is a PIC16F877A. An introduction to it. And then we will be having introduction to compiler softwares and then we will setup our hardware for PICKIT3 based read/write operations and then we will be writing our first code for blinking an LED and then after introducing to libraries of MikroC , we will start coding a new project in each lecture.Following Softwares you will learn here on the way:1- MikroC for PIC.2- Proteus.3- PICKIT 3 programmer tool.4- Timer calculator.5- Nextion editor.6- DWIN DGUS.Following Sensors/Modules/electronics will atleast be covered:1- Light Dependant Resistor (LDR).2- LM-35 temperature sensor.3- 7-segment displays.4- LM016 LCD.5- TIP-122 transistor.6- Resistors.7- Potentiometer.8- Push buttons.9- LEDs.10- DC motor.11- HC-05 bluetooth module.12- HC-12 RF module.13- USB to TTL devices like CH340/FT232.14- Touch buttons modules.15- Limit switch.16- Toggle switch.17- Tilt detection module.18- IR LEDs.19- Obstacle detection module.20- L298N motor driver module.And the list goes on. We will cover as much as much we can in the appointed time.
