|
所在平台: Udemy |
课程主页: https://www.udemy.com/course/advanced-diploma-in-electrical-design-engineering/
课程评论：没有评论
课程名称：电气设计工程高级文凭 课程概述：本课程旨在以经济有效的方式设计安全可靠的处理设施。针对大型电力系统的设计与工程，正式培训项目较为稀缺。重电行业涵盖了发电、输电、配电及使用设备，包括涡轮发电机、锅炉、涡轮、变压器、开关设备等。这些电气设备广泛应用于几乎所有行业，尤其是发电项目、石化、炼油、化工厂、综合钢厂和非铁金属单位等领域。 课程内容包括： 1. 电气工程简介 2. EPC行业概述 3. 与其他部门协调 4. 负载清单的准备 - 负载计划 - 电力供应能力的确定 - 备用能力考虑 - 发电机与主动力的相关性及温度的影响 5. 电气设备选择与尺寸设计 - 电机、变压器、应急发电机等的选择与规格 - 确定中性接地电阻（NGR）、功率电容器组和照明设计 - 照明设备的选择及室内外照明计算 6. 电缆选择、尺寸设计与布局 - 电源和控制电缆的选择与设计 - 低压和高压系统的电缆尺寸设计 - 电缆的路由布局和标记 7. 单线图（SLD）的开发 - 关键SLD与详细SLD的制定 - 照明系统与小功率SLD的设计 8. 接地与防雷设计 - 工业厂房接地的需求与设计计算 - 接地与防雷所需的安装细节和布局设计 9. 测试与系统研究 - 负载流分析 - 短路分析（故障电流计算） - 电机启动研究与继电器协调 通过本课程，学员将全面掌握电气设计的核心知识与技能，为未来的工业项目打下坚实基础。
The goal is to design safe and dependable processing facilities in a cost effective manner. The fact is that there are very few formal training programs that focus on design and engineering of Electrical systems of such big plants The heavy electrical industry has under its purview power generation, transmission, distribution and utilization equipment. These include turbo generators, boilers, turbines, transformers, switchgears and other allied items. These electrical equipment (transformers, switchgears, etc.) are used by almost all the sectors. Some of the major areas where these are used include power generation projects, petrochemical, refineries, chemical plants, integrated steel plants, non-ferrous metal units, etc.Overview:-Introduction of Electrical EngineeringIntroduction of EPC IndustryCoordination with Other DepartmentLoad List:-Preparation of Load ScheduleDetermination of Power Supply CapacityStandby Capacity considerationRating of Generators in Relation toPrime Movers Importance of max and min tempRating of Motors in Relation to their Driven MachinesElectrical Equipment Selection, Sizing:-MotorTransformerEmergency GeneratorNeutral Grounding Resistor (NGR)Power capacitor banks (PCB)AC UPSBattery & Battery ChargerCT/PTBus ductIllumination Design:-IntroductionType of Lighting FixturesSelection of Lighting FixturesPreparation of Fixtures ScheduleIndoor Illumination CalculationOutdoor Illumination CalculationCalculation on SoftwareLighting Layout DesignLighting Installation DetailSmall Power selectionLighting Board ScheduleCable Selection, Sizing & Layout:-Power and Control cable IntroductionCable Selection and SizingCable sizing for Low voltage systemCable sizing for High voltage systemVoltage Drop ConsiderationLet through Energy considerationEarth fault Loop Impedance considerationCable ScheduleCable interconnection ScheduleSelection and Sizing of cable TrayCable tray scheduleCable Drum scheduleConduit SelectionConduit SizingCable Routing LayoutCable TaggingInstallation detailsDevelopment of Single Line Diagram (SLD):-Key SLDDetail SLDLighting system SLDSmall power SLDMetering and Control diagramEarthing & Lightening Protection Design:-Requirement of Earthing in Industrial PlantsEarthing Design calculationsType of Earthing and DetailsEarthing Installation DetailsEarthing Layout DesignLightening Protection RequirementLightening Protection CalculationLightening Installation DetailsLightening Layout DesignTesting / System Studies:-Overview & Load Flow AnalysisShort Circuit Analysis (Fault Level Calculations)Motor Starting StudyRelay- Coordination
